How do I stop "autofill" BOM and associated bubbles from showing certain...
In Creo 3.0 parametric student edition, can I merge an assembly file called bearing.asm to a part file without causing the already finished final assembly to fail regeneration? Essentially, my issue...
View ArticleRe: How do I stop "autofill" BOM and associated bubbles from showing certain...
You can Filter the components or set the BOM to not be Recursive. You can also rename (with the assembly in session) the current bearing assembly, then bring in the 'one piece' assembly and Replace...
View ArticleRe: How do I stop "autofill" BOM and associated bubbles from showing certain...
Thank you for the response. I will try those options when I get home.Is it difficult to set the BOM to not be recursive? The one I use was given to my by the professor.
View ArticleClik here to view.
Re: How do I stop "autofill" BOM and associated bubbles from showing certain...
It is part of the Repeat Region properties. You need to select the whole table, otherwise you get the cell properties.
View ArticleTravou enquanto eu baixa o arquivo,como faço para baixar novamente creo 3.0...
Boa noite. Tenho a versão 2.0 do creo e gostaria de baixar a 3.0 , como faço?tentei e ele travou e apos não consegui mais devido ao site inibir meu acesso.obrigado
View ArticleRe: How do I stop "autofill" BOM and associated bubbles from showing certain...
How about creating a shrinkwrap of the bearing and replacing the assemblies with this at the top level?
View ArticleRe: PTC Creo 3.0 Academic allways install to c:\
Hi, to finish entering custom installation path properly, you have to press ENTER key on the keyboard. MH
View ArticleRe: Travou enquanto eu baixa o arquivo,como faço para baixar novamente creo...
Hi, start download from https://support.ptc.com/appserver/auth/it/esd/academicFree.jsp page. MH
View ArticleClik here to view.
Clik here to view.
Re: Script error in PTC Creo
Hi, my suggestion: 1.]Click No button in error message window 2.]Check option at the bottom of Resource Center window. 3.]Close Resource Center window. 4.]Exit Creo session. 5.]Add following options...
View ArticleClik here to view.
Re: Script error in PTC Creo
None of those seemed to have an effect. The script error still pops up even with the resource browser/community tab disabled.
View ArticleClik here to view.
Re: Script error in PTC Creo
Add the offending site to the hosts file. See https://support.rackspace.com/how-to/modify-your-hosts-file/ Set the address to 0.0.0.0 and the website to dc.ads.linkedin.com This will cause the OS to...
View ArticleClik here to view.
Re: How do I stop "autofill" BOM and associated bubbles from showing certain...
I am unfamiliar with what sheinkwrap means in Creo but I look forward to learning more in the future. Editing the table wasnt too difficult to learn but it was a bit annoying having to do it for each...
View ArticleLimitations of Creo 2.0 Student Verison
I have a homework assignment (attached). I am not asking for any solutions as I am eager to learn. But I am running into an issue with my Creo 2.0 education version. When I am running simulate it pops...
View ArticleRemove Material is Greyed Out
Hello, I looked up my question already but I did not see a good answer for my circumstance. Can anyone help me figure out why my "Remove Material" feature is greyed out? Thanks!
View ArticleRe: Remove Material is Greyed Out
Hi, show us the section of Extrude feature. Is it closed ? MH
View ArticleClik here to view.
Re: Remove Material is Greyed Out
Make sure the first feature is solid and not a surface.
View Article